BOCA RESEARCH, INC.

IDE PLUS VL

 Data bus:                32-bit, VL-bus

 Size:                    Three/quarter-length, half-height card

 Hard drive supported:    Two IDE (AT) Interface drives

 Floppy drives            Two 360KB, 720KB, 1.2MB, or 1.44MB drives
 supported:

[Image]

                              CONNECTIONS

                    Function                           Location

  40-pin IDE(AT) Interface connector                      J1

  4-pin connector - Drive active LED                      J2

  34-pin control cable connector - floppy drive           J3

  10-pin serial port (COM2/4) - internal                  J4

  10-pin serial port (COM1/3) - external                  J5

  25-pin parallel port (LPT1/2) - external                J8

                        USER CONFIGURABLE SETTINGS

              Function
                                           Location
                                                              Setting

  »
      Serial Port 1 (J5) enabled
                                         J7/jumper 1
                                                             pins 1 & 2
                                                               closed


      Serial Port 1 (J5) disabled
                                         J7/jumper 1
                                                             pins 2 & 3
                                                               closed

  »
      Serial Port 2 (J4) enabled
                                         J7/jumper 2
                                                             pins 1 & 2
                                                               closed


      Serial Port 2 (J4) disabled
                                         J7/jumper 2
                                                             pins 2 & 3
                                                               closed

  »
      Serial Port 1 (J5) is set to
      COM1
                                         J7/jumper 3
                                                             pins 1 & 2
                                                               closed


      Serial Port 1 (J5) is set to
      COM3
                                         J7/jumper 3
                                                             pins 2 & 3
                                                               closed

  »
      Serial Port 2 (J4) is set to
      COM2
                                         J7/jumper 4
                                                             pins 1 & 2
                                                               closed


      Serial Port 2 (J4) is set to
      COM4
                                         J7/jumper 4
                                                             pins 2 & 3
                                                               closed

  »
      Parallel Port (J8) enabled
                                         J7/jumper 5
                                                             pins 1 & 2
                                                               closed


      Parallel Port (J8) disabled
                                         J7/jumper 5
                                                             pins 2 & 3
                                                               closed

  »
      Parallel Port (J8) address is
      378h
                                         J7/jumper 6
                                                             pins 1 & 2
                                                               closed


      Parallel Port (J8) address is
      278h
                                         J7/jumper 6
                                                             pins 2 & 3
                                                               closed

  »
      Floppy drive port address is
      3F0-3F7h
                                         J7/jumper 8
                                                             pins 1 & 2
                                                               closed


      Floppy drive port address is
      370-377h
                                         J7/jumper 8
                                                             pins 2 & 3
                                                               closed

  »
      Parallel Port (J8) uses IRQ7
                                         J10/jumper 1
                                                             pins 1 & 2
                                                               closed


      Parallel Port (J8) uses IRQ5
                                         J10/jumper 1
                                                             pins 2 & 3
                                                               closed

  »
      Serial Port 1 (J5) uses IRQ4
                                         J10/jumper 2
                                                             pins 1 & 2
                                                               closed


      Serial Port 1 (J5) uses IRQ7
                                         J10/jumper 2
                                                             pins 2 & 3
                                                               closed

  »
      Serial Port 2 (J4) uses IRQ3
                                         J10/jumper 3
                                                             pins 1 & 2
                                                               closed


      Serial Port 2 (J4) uses IRQ5
                                         J10/jumper 3
                                                             pins 2 & 3
                                                               closed

                        FLOPPY DRIVE CONFIGURATION

            Drive                  J7/jumper 7                 J9

  »          Enabled            pins 1 & 2 closed            Closed

            Disabled            pins 2 & 3 closed             Open